Electromagnetic Flow Meter for Water - Wastewater: Application Note
Sep 29, 2026
Shenzhen, Guangdong Sep 28, 2026 (Issuewire.com) - A water utility does not buy a flow meter because it is elegant. It buys one because the number on the screen has to hold up in a billing dispute, survive a grit-laden storm overflow, and still read within tolerance after five years of chlorinated water. We build magmeters for exactly that kind of abuse. This note is written from our application engineering desk -- the same desk that signs off the lining-and-electrode matrix before a unit leaves the plant -- and it covers what actually decides whether an electromagnetic flow meter works in water and wastewater service, not what the brochure headline implies.
1. Why plants keep coming back to the magmeter
In water and wastewater, the magmeter won more ground than any other principle because it has no moving parts in the wetted path. There is nothing to wear against the flow, nothing to jam with rags, and the pressure drop is effectively zero. For a lift station moving screened sewage, that single fact removes the failure mode that kills most mechanical meters. We still specify turbine and positive-displacement meters for clean, viscous or custody-transfer duties elsewhere, but for conductive liquids with solids, air or chemistry, the magnetic principle is usually the least troublesome.
That said, it is not universal. The one hard rule is conductivity: the liquid must conduct. Below roughly 5 µS/cm, the signal collapses. We have watched more than one installer try to put a magmeter on deionized rinse water and wonder why the reading flatlined. It is not a fault. It is the physics.
2. The physics, stated once and plainly
Faraday's law of induction is the whole game. A conductive fluid moving through a magnetic field induces a voltage. For a meter of fixed bore, that induced voltage is proportional to average velocity:
E = B · L · v
where B is the field flux density, L is the electrode spacing (fixed by the bore), and v is the mean velocity of the liquid. Multiply by the known cross-section and you get volume flow. No inference, no float, no turbine wheel. The meter measures the velocity of a conductor moving through a field, and converts that to volume against geometry it already knows.
Two consequences follow that people underweight. First, because the measurement is geometric and volumetric, density, viscosity, pressure and temperature of the liquid do not enter the equation -- as long as it conducts and the pipe stays full. Second, the signal scales with velocity, so any condition that distorts the velocity profile (air pockets, partly full pipe, swirl from a bad elbow) distorts the reading directly. Most "magmeter is wrong" calls we get are actually "the pipe is not full" or "there is a bubble train" calls.
3. Reading the datasheet like an engineer
Buyers fixate on the accuracy number. It matters, but it is the least of what breaks a water application. Here is the order we actually check.
Accuracy class. For water, reputable magmeters sit at ±0.2% to ±0.5% of rate depending on bore and lining. Smaller bores tend to hold the tighter class. For custody transfer of potable water we treat ±0.2% as the floor and require a certified instrument.
Repeatability. Often ±0.1% or better. This is what matters for dosing control loops even when absolute accuracy is looser.
Turndown (range ratio). A good magmeter holds 100:1 or more. That is the difference between reading the night-line trickle and the storm peak on the same sensor. We have replaced meters that were "fine" but had a 10:1 turndown because the plant's low-flow leakage accounting was useless.
Lining and electrode compatibility. This is where water and wastewater diverge most. We cover it below.
Empty-pipe detection. Non-negotiable for lift stations and any suction application. If the pipe runs dry, the meter must alarm, not freeze at a stale value.
Grounding provision. Non-conductive linings need a ground path through ground rings or ground electrodes. Miss this and the reading wanders with the plant earth.
Output and comms. 4-20 mA plus pulse is the baseline. HART or Modbus RTU/TCP earns its place the moment the signal feeds a SCADA or a dosing controller.
4. Lining selection -- the matrix that decides service life
The lining is the only thing between the process and the sensor body. Pick wrong and you are pulling the meter in eighteen months. Our standard selection matrix for water duties:
Media conditionRecommended liningWhyWatch-outsClean potable water, ambientPTFE or PFAinert, smooth, certifiablecost; needs ground ringRaw water, slight abrasionHard rubber / Ebonitetough, economicaltemperature cap ~60 °CWastewater, grit, sludgePolyurethane (PU)best abrasion resistancenot for strong solventsChemically aggressive dosingPFAbroad chemical resistance, high temppremiumHigh-temperature effluentPFA / FEPstable to ~180 °Cliner adhesion at flangesGeneral sewage, mildNeoprene (CR)cheap, decent wearswell with some organics
For drinking-water service the lining has to clear the local potable-contact certification -- WRAS in the UK, NSF/ANSI 61 in North America, KTW-BWGL in Germany. We keep dedicated potable-grade linings and do not mix them with industrial stock, because the certification chain is part of the product, not a sticker.
A note from the field: polyurethane beats PTFE hands down for grit, but it hates aromatic solvents and some hydrocarbons. If the wastewater stream ever sees fuel interceptors or solvent recovery, we move the lining up to PFA and accept the cost. The wrong lining choice is the most expensive cheap decision in this whole spec.
5. Electrode and grounding -- the part people get wrong
Electrodes pick up the induced voltage. In clean water, 316L stainless is fine. The moment you add chlorination, hydrogen sulfide, or abrasive grit, the choice changes:
- Chlorinated / aggressive: Hastelloy C-276 or titanium.
- Sludge with scaling tendency: tantalum, or a platinum-coated pair, or -- our preference for fouling service -- a scraper-type (self-cleaning) electrode that the operator cycles weekly.
- High abrasion + corrosion: Hastelloy C with a hardened face, or ceramic.
Grounding is where installations go bad. A PTFE-lined meter is electrically insulated from the pipe. Without a ground ring or ground electrodes straddling the liner, the measurement reference floats and the signal rides the plant earth noise. We mandate ground rings on every non-conductive-lined meter and document the jumper in the install sheet. Half the "unstable magmeter" service calls we attend are a missing or painted-over ground strap.
Conductivity deserves a sentence of respect. Most municipal water sits well above the 5 µS/cm floor, so it is a non-issue -- until you meter reverse-osmosis permeate or condensate, where it is a hard stop. We ask for the conductivity range on every enquiry for that reason.
6. Installation rules that decide whether it works
We can ship a perfect meter and still watch it fail on site. The rules:
Full pipe, always. A magmeter measures velocity across the whole bore. A partly filled sewer pipe is not a flow meter, it is a guess. On gravity lines we specify an inverted-U or a full-flow weir upstream, or a filling valve. On pumped suction we keep the meter below the source and short-coupled.
Straight run. Ten diameters upstream, five downstream, free of valves and elbows that swirl the profile. Where the pit is cramped we fit a straightening vane rather than accept a distorted profile.
No air at the top. Air collects at high points. We route the meter on a rising run, or put a de-gas point just upstream. Bubble trains read as flow spikes and then dropouts.
Ground and bond. Covered above -- but it belongs in the install section too, because the electrician and the fitter are different people.
Avoid siphon. A siphon above the meter empties the bore mid-span and the reading goes mad. We set the meter below hydraulic grade or break the siphon with an air valve.
One war story: a treatment works complained of 8% over-registration on a stormwater bypass. The meter was perfect. The upstream elbow had no straight run and a persistent vortex threw the profile. Ten diameters of spool and a vane later, the dispute with the neighboring district evaporated.
7. Application notes by duty7.1 Raw water and intake
Large bore (DN300-DN1200 and up), low and variable velocity, sand in suspension. We line with hard rubber for economy and fit 316L or Hastelloy electrodes. Velocity is kept in the 1-2 m/s band to limit abrasion but stay above the low-end turndown floor. Empty-pipe detection is mandatory because intake screens trip and the line drains.
7.2 Drinking water (potable)
Accuracy and certification lead. We use PTFE or PFA lining with potable-grade certification, ±0.2% accuracy, and -- for billing -- a unit cleared to MID (Measuring Instruments Directive 2014/32/EU) or OIML R49 for cold-water meters. Pulse output drives the revenue meter; the 4-20 mA feeds the SCADA trend. We dual-stamp the calibration certificate because the water authority audits it.
7.3 Wastewater and sludge
This is the harsh end. Grit abrades linings; rags and grease foul electrodes; hydrogen sulfide corrodes. We line with polyurethane for grit, step electrodes up to Hastelloy C or ceramic for abrasion, and specify scraper electrodes where fatbergs form. Turndown has to cover the dry-weather trickle and the storm surge on one sensor. We add empty-pipe detection because lift stations transiently run dry.
7.4 Chemical dosing
Chlorine (sodium hypochlorite), PAC, ferric, and polymer (PAM) are dosed in small bore (DN15-DN50) at low, steady flow. The liquid is corrosive and sometimes sticky. PFA lining, tantalum or platinum electrodes, and a pulse output into the dosing controller. We keep velocity modest to avoid shear damage to polymer chains in PAM lines -- too fast and the flocculant is partly sheared before it doses.
8. Empty-pipe detection and fouling maintenance
Empty-pipe detection uses the change in capacitance between the electrodes and the (absent) liquid. When the bore drains, the meter flags it and holds or zeros the output instead of reporting a phantom flow. For a lift station this single feature stops a pump running dry from being logged as throughput.
Electrode fouling is the other routine issue. Grease and scale build an insulating film and the signal drifts. Options, in order of preference: scraper electrodes cycled on a schedule; a periodic chemical clean (citric or inhibited acid, commensurate with lining); or -- for stubborn duty -- a removable electrode the crew swaps without pulling the spool. We do not recommend ultrasonic cleaning on lined sensors; the liner does not like it.
9. Signal, batch control and the dosing loop
The meter is only as useful as what eats its signal. Our standard fit:
- 4-20 mA for rate, wired to the PLC or recorder.
- Pulse / frequency for totalized volume -- the revenue and dosing signal.
- HART for config and diagnostics over the loop.
- Modbus RTU/TCP where the plant runs open protocol.
For dosing, the pulse output drives a batch controller: dose a fixed volume of PAC per tank turnover, closed-loop, no operator in the loop. We have seen polymer savings of 10-15% just from replacing a hand-dosed scoop with a magmetered batch because the dose became repeatable instead of hopeful. The magmeter does not save chemical by magic; it saves chemical by making the dose a measured thing.
10. How the magmeter comparesPrincipleConductive liquidsSolids / sludgeZero moving partsTurndownNotesElectromagneticyesexcellentyes~100:1needs conductivity >5 µS/cmUltrasonic (clamp)yespoor (scatter)yesmoderateno pipe cut, but solids scatter signalUltrasonic (inline)yesfairyesmoderatebetter than clamp, still grit-sensitiveVortexyespooryes~10-20:1needs min velocity, bluff-body wearTurbineclean onlynonomoderatebearing wear, not for sewageOpen-channel (weir)yesgoodyeswideneeds free surface, civil works
For full-pipe conductive water with grit, the magmeter wins on ruggedness and turndown. For non-conductive or ultra-pure water, it is disqualified and we move to ultrasonic or coriolis. For free-surface channels, a magmeter cannot read at all and the weir or flume takes over. Our coriolis mass flow meter covers the non-conductive and mass/custody cases; the two principles are siblings in the same flow portfolio, not rivals.
11. Sizing worked example
A regional works needs to meter raw-water intake, expected 800 m³/h peak, 120 m³/h night line. They propose DN300.
Cross-section A = ·(0.30)²/4 = 0.0707 m². Peak velocity v = 800 / (3600 · 0.0707) = 3.14 m/s. Night velocity v = 120 / (3600 · 0.0707) = 0.47 m/s.
At 3.14 m/s the peak is above our 3 m/s abrasion comfort line for gritty raw water, and at 0.47 m/s the night line is well inside the turndown but near the lower accuracy band. We recommend DN350 instead: peak drops to 2.31 m/s (lining-friendly), night rises to 0.35 m/s (still readable on a 100:1 turndown). Lining hard rubber, electrodes 316L, ground rings, empty-pipe on. The slight oversize costs little and keeps the meter in its happy range for the whole operating envelope. Sizing to the peak alone is the classic error; we size to the envelope.
12. Calibration and certifications
We calibrate every magmeter on a water rig -- volumetric or weighbridge tank -- before it ships, and stamp the certificate to the stated accuracy class. For potable and custody duties the unit carries the applicable approvals:
- MID (2014/32/EU) and OIML R49 for cold-water custody transfer in the EU and aligning markets.
- WRAS / NSF-61 / KTW-BWGL for potable-contact linings.
- ISO 9001 as the baseline quality system.
- ATEX / IECEx where the location is classified (gas or dust zone).
- IP67 / IP68 rating matched to the duty -- IP68 for permanent submersion in wet wells.
We keep the calibration rig in-house because sending a DN600 sensor to a third party is neither fast nor cheap, and our own bench lets us re-certify returned units in days, not weeks. The certificate chain -- material, lining cert, calibration, approval -- is what a water authority actually audits, and we treat it as part of the product rather than paperwork.
13. What we actually build
We are not a reseller with a logo. We machine the flow tube, weld the housings, wind and pot the excitation coils, bond the linings, and calibrate on our own rig -- design, manufacture, and sales under one roof. That vertical span matters when something is wrong at 2 a.m.: the person who answers the call can trace the unit to the coil batch and the calibration record, not to a distributor three companies away.
On the technology side, our excitation uses low-frequency three-value square-wave drive to suppress zero drift and quadrature interference, with dual-frequency excitation available for heavy slurry duty where electrode noise would otherwise corrupt the signal. We offer OEM and ODM builds for integrators who need the sensor under their own name, with the same calibration discipline. One accountable entity, from the lining bond to the certificate -- that is the part no catalog paragraph conveys until something fails.
14. When not to use a magmeter
- Non-conductive liquids (DI water, oils, most solvents) -- below the conductivity floor.
- Gases or steam -- no conductor, no signal.
- Free-surface / open channel -- needs a weir or flume instead.
- Very low flow in a huge bore -- size to the envelope, do not expect a DN600 to read the dribble honestly.
Where those constraints bite, we point to our coriolis or ultrasonic lines rather than force a square peg. The right meter is the one that reads true for the actual liquid, not the one on the shelf.
15. Spec checklist and next step
Before you issue the enquiry, lock these down: liquid and conductivity range, solids content and size, temperature and pressure, bore and expected velocity envelope, custody or control intent, lining and electrode allowance, and the approvals your authority demands. Send us that and we return a sized proposal with the lining-electrode matrix and the calibration certificate path.
If you are scoping a water or wastewater project and want the sizing checked against your actual duty, reach the application desk through the contact page and we will work the envelope with you -- including which principle in our flow portfolio actually fits, not just the magmeter.
Source :SHENZHEN LONNMETER GROUP
This article was originally published by IssueWire. Read the original article here.
KCCI, audit authority collaborate to resume construction of 4,000 public housing units
The audit authority has cleared a key hurdle for six stalled public housing projects totaling nearly 4,000 units after the Korea Chamber of Commerce and Industry (KCCI) sought a preliminary consultation on behalf of builders struggling with soaring construction costs. The KCCI said on Tuesday that the Board of Audit and Inspection (BAI) determined that project costs for the six sites, covering 3,936 housing units, can be recalculated to reflect current market conditions. The case marks the KCCI’s first use of the consultation program since it was opened to private organizations in May. “Companies have faced difficulties for a long time, but this was not an issue they could easily make a decision on,” Lee Jong-myung, head of the KCCI's industry innovation division, said. “The BAI's decision to open its doors to the private sector has added another channel for resolving corporate difficulties, and its first result will benefit the public through housing supply.” The six projects are part of a public-private housing program, with public agencies providing the land while private bu
Private sector's role increased in 5th Nuri launch
Private companies played a significantly greater role in the successful fifth launch of Korea’s Nuri rocket on Wednesday, signaling that the country’s efforts to keep pace with the global shift toward a private sector-led “New Space” era are gaining momentum. The Nuri rocket completed its fifth launch and 20-minute-long flight successfully after lifting off at the Naro Space Center in Goheung, Jeonnam-Gwangju Special Metropolitan City, at 12:25 p.m. The most notable change in the latest launch was not the rocket itself, but the growing presence of private-sector personnel at the launch site. Hanwha Aerospace has overseen the manufacturing of the Nuri rocket as its system integrator since the fourth launch on Nov. 27 last year, but this time, its role expanded to the consoles at the launch control center. Hanwha Aerospace deployed 42 staffers for the fifth launch. They participated in operations at 20 of the 22 consoles responsible for launch vehicle systems, and at 18 of them, Hanwha employees directly operated the controls instead of specialists from the Korea Aerospace Researc
![[EXPLAINER] How AI emerged as new threat in Korea's bank hacking crisis](https://newsimg.koreatimes.co.kr/2026/10/07/77d98bb7-f23e-430d-be94-38ae9821547a.jpg)
[EXPLAINER] How AI emerged as new threat in Korea's bank hacking crisis
Hackers once had to manually test security defenses, identify vulnerabilities and work out how to exploit them. Now, artificial intelligence (AI) can do much of that work, requiring little human input. That possibility is at the center of Korea's latest security crisis in the financial sector, as investigators have found traces of an AI-powered autonomous penetration-testing tool in a series of recent cyberattacks on the country's major banks. Since last week, Shinhan Bank, KB Kookmin Bank, Hana Bank, Yegaram Savings Bank and BNK Busan Bank have all reported data breaches, while Woori Bank and NH NongHyup Bank have detected signs of hacking attempts, though no data leaks were confirmed. Shinhan Bank reported that about 25,000 customers were affected, with personal information including names, phone numbers, annual income and loan limits exposed. KB Kookmin reported 119 affected customers, while Hana Bank said personal information belonging to 89 customers was exposed. The hacking spree has drawn particular concern after investigators reportedly found traces of an AI-powered tool known as
SK Energy, HD Hyundai Oilbank face fines over alleged fuel price fixing
SK Energy and HD Hyundai Oilbank may face sanctions from the Fair Trade Commission (FTC) over allegations that they colluded on gasoline, diesel and kerosene prices, with combined fines potentially reaching 4.63 trillion won ($3.45 billion). The antitrust regulator said Wednesday that it sent a review report to the two companies, formally launching deliberations over the alleged price-fixing case. The FTC said the alleged collusion lasted from February 2022, shortly before Russia's invasion of Ukraine, through March this year, shortly after the outbreak of the war in Iran. The case covers petroleum products that are essential to household and economic activity. Korea's oil refining industry is highly concentrated, with SK Energy, HD Hyundai Oilbank, GS Caltex and S-Oil accounting for about 98 percent of the domestic market. According to the FTC, SK Energy and HD Hyundai Oilbank exchanged information on the prices of gasoline, diesel and kerosene, including provisional prices, final prices and sales policies. The regulator also determined that the two companies colluded on prices followin
Beef tallow remains hurdle to Charrr's global expansion
Countries’ regulations on imported foods containing beef tallow pose a hurdle for Samyang Foods as the Korean instant noodle giant seeks to expand exports of its latest black bean sauce instant noodles, Charrr. The company has established Buldak as a massively popular product around the globe without using beef tallow, selling 10 billion units and generating cumulative sales of 7 trillion won ($5.2 billion) as of June. Unlike the spicy, brothless instant noodle brand, however, Charrr uses beef tallow as a key ingredient to give its sauce a rich, beefy flavor. Charrr is not Samyang’s first instant noodle product using beef tallow. The company launched Samyang 1963 in November last year with the ambitious goal of reviving the “forgotten” taste of its first instant noodle product, Samyang Ramen, which was introduced in 1963 and used beef tallow. Samyang Ramen, introduced by the late company founder Chun Joong-yoon to help feed a population suffering from widespread poverty at the time, remains a cornerstone of the company’s identity. Its use of beef tallow has now become part of
Bank data breach victims step up calls for compensation
A growing number of customers affected by a string of recent personal data breaches at major commercial banks and other financial firms appear to be turning to class action lawsuits in pursuit of compensation, according to industry officials, Wednesday. The banks have pledged to fully compensate customers whose losses, including those from voice phishing scams, are found to have directly resulted from the leaks. But proving that a loss was caused by a specific data breach can be difficult in practice, and the banks have yet to set out clear standards for determining which claims would qualify, prompting some victims to resort to legal action. Seven financial firms have reported information leaks so far, including three of the country’s largest commercial lenders — Shinhan Bank, KB Kookmin Bank and Hana Bank. Shinhan reported the largest breach, affecting around 25,000 people, followed by 119 at KB Kookmin and 89 at Hana Bank. The exposed data includes customers’ names, contact details, resident registration numbers, annual income and loan limits. The combination of personal and fin
![[COVER STORY] Nuri rocket successfully completes 5th flight](https://newsimg.koreatimes.co.kr/2026/10/07/6a8cafff-abc8-4ebb-86ed-8bb7b1eb07d3.jpg)
[COVER STORY] Nuri rocket successfully completes 5th flight
Korea’s domestically-developed Nuri rocket successfully carried out its mission in its fifth launch Wednesday, sequentially deploying 14 out of the 15 satellites it carried into their target orbit. The key objective of the fifth launch was to safely deploy the five microsatellite constellations, and its success has demonstrated Korea's increased multisatellite launch capabilities, taking another step toward privately-led commercial launch services. The rocket lifted off from the launchpad at the Naro Space Center in Goheung, Jeonnam-Gwangju Special Metropolitan City, at 12:25 p.m. and completed its roughly 20-minute flight at around 12:45 p.m. The rocket separated its first stage about two minutes after liftoff, followed by the second stage about four and a half minutes into the flight. At around 12:40 p.m., it reached an altitude of 570 kilometers and completed the sequential deployment of five New-space Earth Observation Satellite Constellation for National Safety (NEONSAT) microsatellites (satellites No. 2 to 6), its primary payload, along with nine of the 10 CubeSats it carried. In
AMD to establish AI research center in Korea this year, hire hundreds
U.S. chip giant AMD announced Wednesday that it plans to establish an artificial intelligence (AI) research center in Korea by the end of this year and hire hundreds of researchers as part of broader AI cooperation between the company and Korea. The announcement came during a meeting between AMD CEO Lisa Su and Second Vice Minister of Science and ICT Ryu Je-myung in Seoul. AMD also plans to help develop graduate-level AI and AI transformation talent and collaborate with Korea on a reference model for heterogeneous AI computing. The model would combine AMD’s central processing units (CPUs) and graphics processing units (GPUs) with domestically developed neural processing units (NPUs). The meeting, arranged by the Ministry of Science and ICT, served as an interim review of AI cooperation agreed upon by the ministry and AMD during President Lee Jae Myung’s attendance at the San Francisco AI Summit in July. AMD also outlined plans to work with Korea’s private sector to create new business opportunities. At a subsequent roundtable with 13 Korean companies involved in AI infrastructure, c
OpenAI releases new batch of math breakthroughs
OpenAI released a new batch of mathematics breakthroughs on Tuesday following calls from AI researchers and developers to slow the growth of the technology. The company released 377 results that cover different physics, mathematical and other scientific problems solved by an OpenAI internal frontier model not yet available to the public. “Towards acceleration of scientific...
IMF chief urges countries to do more to curb debt and regulate AI
Countries both rich and poor must take faster action to cut debt and counter growing inequality as their economies weather a triple whammy from the artificial intelligence boom, heavy borrowing and shocks from wars in the Middle East and Ukraine, the head of the IMF said Wednesday. “Some very tough political choices stare us in...
China’s open-weight AI models are winning global users. Who is capturing the value?
China’s open-weight artificial intelligence models are taking off globally, but much of the money they generate is flowing to third-party providers rather than the companies that create them, according to a new study. Developers including DeepSeek and Moonshot AI make their model weights – essentially the “brains” of their AI systems – freely available for download. This strategy, which has accelerated global adoption over the past two years, allows other companies to run the models on their own...
Why Trump chose these leaders to head his 'Super Intelligence Force'
President Trump’s selection of four administration officials to head up his new “Super Intelligence Force” is offering a window into how the White House will approach AI in the face of pressure over its risks. The group of government leaders each reflect different priorities of the Trump administration after months of mixed messaging on the...
YOUR NEWS, OUR NETWORK.
Do you have Great News you want to tell the world?
Be it updates about your business or your community, you can make sure that it’s heard by submitting your story to our network reaching hundreds of news sites across 6 verticals.